Getting Familiar with Plumbing: The First Step for When Installing a Bathtub
Getting Familiar with Plumbing: The First Step for When Installing a Bathtub
Blog Article
The article author is making a few good points on A Step-by-Step Guide to Installing a Bathtub in general in this post on the next paragraphs.
Mounting a tub isn't specifically brain surgery, yet it does need solid plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately challenging job. If the old bathtub is easily obtainable, the task can move quickly; if you need to open a wall surface to get rid of the old tub and also position the new tub, the job is a lot harder. In either case, the job is within a residence handyman's abilities, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Make sure you have certified yourself for the task as well as are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed project, it is much better to consider utilizing one prior to you start. Chances are you may require a specialist plumber to make tube links.
This article will certainly aid you set up a new bath tub in your bathroom if you have currently bought a brand-new bathtub as well as do not need to change the arrangement of your previous water supply pipes.
Your devices as well as product list ought to comprise the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be fairly bothersome because of the limited accessibility that is often the case.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have been gotten rid of, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washers are in place in between the faucet and also the sink. Safeguard the faucet in position with the maker given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular tap adapters. The previous type ought to be connected to the tap ends initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Using the two wooden boards under its feet, place the bath tub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bath tub till the level checks out level.
To set up faucets, fit all-time low of the outermost adaptable tap connector to the suitable supply pipe by making a compression sign up with; then do the same for the other faucet.
Turn on the water supply and inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the tub as well as likewise examine the overflow outlet and the normal electrical outlet for leakages.
Ultimately, deal with the bath paneling as explained in the supplier's user's manual. Tiling and also sealing around the bathtub should wait until the bath tub has actually been utilized at least when as this will resolve it into its last position.
Planning for the Setup
First of all, the sustaining framework supplied with the bathroom ought to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the tap block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps unit to avoid stress on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps making use of 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet through the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be fitted in its last placement.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to break a stiff seal, causing the water to permeate the wall between the bathroom and also the tiling, bring about complications with wetness as well as possible leaks to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components and also fittings. They are sold in tubes as well as cartridges, and can sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill the bath tub with water prior to sealing, to enable the activity experienced when the bathtub remains in use. The sealer can fracture relatively early if you do not take into consideration this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily readily available on the marketplace. It is recommended to fit the tiles using water-resistant or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very interested in How to Install a Bathtub Yourself and I'm hoping you appreciated the post. Enjoyed our content? Please share it. Help other people check it out. We treasure reading our article about A Step-by-Step Guide to Installing a Bathtub.
At This Website Report this page